1.與山東不銹鋼制造廠家一起商定需要的表面加工，最好準備一個樣品，作為今后批量生產的標準。With the Shandong stainless steel manufacturers agreed to the needs of the surface processing, it is best to prepare a sample, as the future of mass production standards.

2.大面積使用時（如復合板，必須保證所用的基底卷板或卷材采用的是同一批次。The use of large area (such as composite board, you must ensure that the basement membrane coil or is used in the same batch.

3.山東不銹鋼雕塑專家認為，在許多建筑應用中，如：電梯內部，盡管手印可以擦掉，但很不美觀。如果選用布紋表面，就不那么明顯了。在這些敏感的地方一定不能使用鏡面不銹鋼。Shandong stainless steel sculpture experts believe that in many construction applications, such as: inside the elevator, although fingerprints can be erased, but very beautiful. If the grain surface is not so obvious. Mirror stainless steel must not be used in these sensitive areas.

4.選擇表面加工時應考慮到制作工藝，例如：為了除去焊珠，可能要對焊縫進行修磨，而且還要恢復原有的表面加工。花紋板很難甚至無法滿足這一要求。Selection of surface processing should take into account the production process, such as: in order to remove the welding bead, it may be to repair the welding seam, but also to restore the original surface processing. Pattern plate is difficult to meet the requirements.

5.對于有些表面加工、修磨或拋光的紋路是有方向性的，被稱為單向的。如果使用時使這種紋路垂直而不是水平，污物就不易附著在上面，而且容易清洗。For some surface processing, grinding or polishing of the lines are directional, known as one-way. If it is used to make the grain vertical rather than horizontal, dirt is not easy to attach to it, and it is easy to clean.

6.山東不銹鋼雕塑廠家認為，無論采用哪種精加工都需要增加工藝步驟，因此要增加費用，所以，選擇表面加工時要慎重。因此，建筑師、設計人員和制造廠家等有關人員需要對不銹鋼的表面加工有所了解。通過彼此之間的友好合作和相互交流，一定會獲得所期望的效果。Shandong stainless steel sculpture manufacturers believe that no matter what kind of finishing are required to increase the process steps, so to increase the cost, therefore, the choice of surface processing should be careful. Therefore, architects, designers and manufacturers and other relevant personnel need to understand the surface of stainless steel. Through friendly cooperation and mutual exchange, the desired effect will be obtained.

7.根據山東不銹鋼雕塑專家的經驗，我們不建議使用氧化鋁作磨料，除非在使用過程中十分小心。最好是使用碳化 硅磨料。According to the experience of Shandong stainless steel sculpture experts, we do not recommend the use of alumina as abrasive, unless very carefully in the course of use. It is best to use silicon carbide abrasive.